Уязвимости linux · Страница 35

wifi: virt_wifi: free skb when disconnected

In the Linux kernel, the following vulnerability has been resolved: wifi: virt_wifi: free skb when disconnected When the simulated link is disconnected, virt_wifi_start_xmit() returns NET_XMIT_DROP without freeing the skb. dev_hard_start_xmit() treats this return value as consumed, so every packet sent while disconnected leaks its skb. Free the skb before returning the drop status.

• Обновитесь до 6.12.113-1

wifi: libipw: reject too-short beacon and probe responses

In the Linux kernel, the following vulnerability has been resolved: wifi: libipw: reject too-short beacon and probe responses libipw_process_probe_response() and the libipw_network_init() call it makes assume the frame contains the full 36-byte beacon and probe response prefix, but the ipw2100 and ipw2200 receive paths only establish that a management frame carries the generic 24-byte three-address header. libipw_network_init() then computes the information element length as stats->len - sizeof(*beacon) stats->len is a u16 and sizeof() has type size_t, so the subtraction is evaluated as size_t and wraps instead of going negative. Trunc

• Обновитесь до 6.12.113-1

wifi: libipw: reject too-short association responses

In the Linux kernel, the following vulnerability has been resolved: wifi: libipw: reject too-short association responses libipw_handle_assoc_resp() reads the capability, status and aid fields of the 30-byte association response prefix and then computes the information element length as stats->len - sizeof(*frame) stats->len is a u16 and sizeof() has type size_t, so the subtraction is evaluated as size_t and wraps instead of going negative. Truncating that to the u16 length parameter of libipw_parse_info_param() turns a frame shorter than the fixed fields into a length near 64 KiB, and the parser then reads past the receive buffer. Both

• Обновитесь до 6.12.113-1

IB/IPoIB: Avoid restoring OPER_UP after multicast flush

In the Linux kernel, the following vulnerability has been resolved: IB/IPoIB: Avoid restoring OPER_UP after multicast flush ipoib_ib_dev_flush_light() temporarily clears IPOIB_FLAG_OPER_UP to prevent multicast joins while ipoib_mcast_dev_flush() is running, and restores the flag afterwards if it was previously set. This restore races with ipoib_ib_dev_down(). If the interface is brought down while the flush is in progress, ipoib_ib_dev_down() clears IPOIB_FLAG_OPER_UP, but the flush path may set it again after the device has already gone down. Since commit 894021a75291 ("IB/ipoib: Make the carrier_on_task race aware"), ipoib_mcast_carrier

• Обновитесь до 6.12.113-1

wifi: cfg80211: don't get the radio mask for netdev-less wdevs

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: don't get the radio mask for netdev-less wdevs cfg80211_calculate_bi_data() calls rdev_get_radio_mask() with wdev->netdev, which can be NULL and then crashes in mac80211. To avoid that, invert the order of checks since wdev->netdev is always valid for beaconing interfaces.

• Обновитесь до 6.12.113-1

wifi: cfg80211: check IP header size in cfg80211_classify8021d()

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: check IP header size in cfg80211_classify8021d() A frame that looks like IP can be transmitted, but be too short, so the DS field is read incorrectly: BUG: KMSAN: uninit-value in cfg80211_classify8021d+0x99d/0x12b0 net/wireless/util.c:1027 cfg80211_classify8021d+0x99d/0x12b0 net/wireless/util.c:1027 ieee80211_select_queue+0x37a/0x9e0 net/mac80211/wme.c:180 __ieee80211_subif_start_xmit+0x60f/0x1d90 net/mac80211/tx.c:4304 ieee80211_subif_start_xmit+0xa8/0x6d0 net/mac80211/tx.c:4538 ... packet_sendmsg+0x9173/0xa2a0 net/packet/af_packet.c:31

• Обновитесь до 6.12.113-1

dmaengine: Fix device kref underflow in dma_chan_put()

In the Linux kernel, the following vulnerability has been resolved: dmaengine: Fix device kref underflow in dma_chan_put() dma_chan_get() takes chan->device->ref only on the slow path: /* no kref on fast path */ if (chan->client_count) { __module_get(owner); chan->client_count++; return 0; } if (!try_module_get(owner)) return -ENODEV; if (!dma_device_get(chan->device)) { // calls kref_get_unless_zero() dma_chan_put() drops the ref unconditionally, so every fast-path get/put pair drops one extra device reference. The bug fires when two conditions hold together: a non-private provider has a persistent client holding chan->clie

• Обновитесь до 6.12.113-1

dmaengine: fix use-after-free in dma_chan_put() and dma_release_channel()

In the Linux kernel, the following vulnerability has been resolved: dmaengine: fix use-after-free in dma_chan_put() and dma_release_channel() When dma_device_put() drops the last reference on chan->device->ref, dma_device_release() runs and may free the dma_device along with its channels. dma_chan_put() then still reads chan->device->owner via dma_chan_to_owner() for the trailing module_put(). KASAN catches it: slab-use-after-free in dma_chan_put+0x3e6/0x4c0 Read of size 8 by task insmod/6319 Freed by task 6319: kfree+0x225/0x470 dma_chan_put+0x395/0x4c0 dmaengine_put+0xf8/0x160 Cache the module owner in dma_chan_put() before

• Обновитесь до 6.12.113-1

dmaengine: wait for RCU readers before releasing dma_device

In the Linux kernel, the following vulnerability has been resolved: dmaengine: wait for RCU readers before releasing dma_device dma_issue_pending_all() walks the dma_device_list with list_for_each_entry_rcu() under rcu_read_lock(). dma_device_release() unlinks the device with list_del_rcu() and then calls device->device_release() (which in many drivers, such as plx_dma.c, directly calls kfree()). Because there is no grace period between unlinking the device and freeing it, concurrent RCU readers in dma_issue_pending_all() can access the device after it has been freed. The lockless walk originally relied on clients holding a dmaengine refe

• Обновитесь до 6.12.113-1

wifi: cfg80211: don't free driver-owned scan requests

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: don't free driver-owned scan requests When an interface goes down while a scan is running, cfg80211 completes the scan towards userspace and frees the scan request. However, the driver can be convinced that it owns the request, since the cancellation is (intended to be) asynchronous. The WARN_ON() in the netdev notifier was meant to catch this, but it's not actually avoidable, so it triggers and we get a UAF in scan_done(). There doesn't seem to be a great way around it, so just track that the driver is still convinced it owns the request, and then just fr

wifi: cfg80211: only group hidden BSSes with beacon entries

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: only group hidden BSSes with beacon entries When a probe response for an unknown BSS comes in, __cfg80211_bss_update() looks for an existing entry with the same BSSID and a hidden (zero-length or NUL-filled) SSID, and if it finds one it groups them, using the beacon IEs from the existing entry. But that could find another entry without a beacon, if it was also from a probe response (with SSID), so there's a group without beacon elements. If a beacon with a hidden SSID for that BSSID arrives later, cfg80211_combine_bsses() goes looking for the probe respons

• Обновитесь до 6.12.113-1

wifi: cfg80211: don't filter by BSS type when removing stale entries

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: don't filter by BSS type when removing stale entries When an assoc AP switches to a channel that already has a BSS entry, cfg80211_update_assoc_bss_entry() removes that entry before rehashing the real one, since the two would otherwise collide in the BSS rbtree. The lookup for that entry also required it to match the connection's BSS type, so an entry advertising e.g. the IBSS capability bit was left in place, and the following cfg80211_rehash_bss() then ran into it: WARN_ON(!cmp) Changing the type shouldn't really happen, but can be triggered by a rogu

• Обновитесь до 6.12.113-1

wifi: cfg80211: ibss: ref BSS entry for joined event

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: ibss: ref BSS entry for joined event When the IBSS is joined, we only record the BSSID/channel in the event and look up the BSS entry when processing it. However, that's racy, e.g. a new scan with NL80211_SCAN_FLAG_FLUSH can remove it, causing a warning in the event work: !bss WARNING: net/wireless/ibss.c:37 at __cfg80211_ibss_joined+0x3d3/0x440 Workqueue: cfg80211 cfg80211_event_work cfg80211_process_wdev_events+0x39f/0x5b0 net/wireless/util.c:1144 cfg80211_process_rdev_events+0xa1/0x110 net/wireless/util.c:1179 cfg80211_event_work+0x2f/0x40

wifi: mac80211: don't start a ROC while scanning

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: don't start a ROC while scanning The ROC work can be pending when a scan starts (which requires ROC list to be empty, but that's possible), and then a new ROC can be added to the list and the work will pick it up. Avoid starting that ROC if a scan made it between things, as otherwise we'll hit a warning later: WARNING: net/mac80211/offchannel.c:404 at ieee80211_start_next_roc+0x256/0x2d0 Workqueue: events_unbound cfg80211_wiphy_work Call Trace: __ieee80211_scan_completed+0x4fd/0xe40 net/mac80211/scan.c:537 ieee80211_scan_work+0x472/0x1ff0 net/m

• Обновитесь до 6.12.113-1

wifi: mac80211: don't offload TC setup on AP_VLAN interfaces

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: don't offload TC setup on AP_VLAN interfaces AP_VLAN interfaces are purely virtual, so don't try to offload TC setup to drivers. We can't really use the AP interface either since we may not know it all the time, and it could technically even change. Just reject the TC offload so things get done in software.

• Обновитесь до 6.12.113-1

wifi: mac80211: abort chanswitch when leaving a mesh

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: abort chanswitch when leaving a mesh The code in ieee80211_stop_mesh() leaves CSA active, but leaving the mesh released the channel context, so the CSA finalize work crashes: Oops: general protection fault, probably for non-canonical address 0xdffffc0000000003 KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f] RIP: 0010:ieee80211_put_srates_elem+0x42/0x640 net/mac80211/util.c:3272 Call Trace: ieee80211_mesh_build_beacon+0xa83/0x1b50 net/mac80211/mesh.c:1093 ieee80211_mesh_rebuild_beacon+0xc7/0x170 net/mac80211/mesh.

• Обновитесь до 6.12.113-1

wifi: mac80211: reset state when starting AP fails

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: reset state when starting AP fails ieee80211_start_ap() can set enable_beacon (and beacon_int) and fail later, leaving it set forever. Scanning can then attempt to restore beaconing on such an interface, leading to: Oops: divide error: 0000 [#1] SMP KASAN NOPTI RIP: 0010:mac80211_hwsim_link_info_changed+0xca7/0xf00 Call Trace: drv_link_info_changed+0x413/0x860 net/mac80211/driver-ops.c:495 ieee80211_link_info_change_notify+0x24b/0x3c0 net/mac80211/main.c:427 ieee80211_offchannel_return+0x381/0x580 net/mac80211/offchannel.c:160 __ieee80211_

• Обновитесь до 6.12.113-1

wifi: mac80211: reset the LED state when ifup fails

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: reset the LED state when ifup fails When the first interface comes up, the radio LED is turned on. This can start the TPT trigger timer, which continues running. But if bringing up the interface fails then the timer keeps running and won't be stopped by anything, eventually it can be freed: ODEBUG: free active (active state 0) object: ffff888127e12130 object type: timer_list hint: tpt_trig_timer+0x0/0x300 net/mac80211/led.c:145 WARNING: CPU: 0 PID: 5923 at lib/debugobjects.c:612 debug_print_object+0x1a2/0x2b0 debug_check_no_obj_freed+0x4b7/0x600 lib

wifi: mac80211: only operate on TDLS peers in the TDLS code

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: only operate on TDLS peers in the TDLS code ieee80211_tdls_oper() can operate on the AP station, which then yields various warnings when the AP station is removed then or at a later point in time after being confused for a TDLS peer. Always check that the station is a TDLS peer.

wifi: mac80211: unlist vifs when their netdev is unregistered

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: unlist vifs when their netdev is unregistered mac80211 only removes vifs from the local->interfaces list when an interface is removed via ieee80211_if_remove(), before it unregisters the netdev. However, it's possible for a netdev to be unregistered without going through that: When the netns that holds the wiphy is destroyed, the wiphy is supposed to move to the init_ns, but that can run into allocation failures. Then, mac80211 has an interface listed that doesn't exist, and will eventually hit BUG: failure at net/wireless/core.h:141/wiphy_to_rdev()! .

• Обновитесь до 6.12.113-1