wifi: mt76: mt7996: clear stale link state on full reset
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: clear stale link state on full reset
After a full chip reset, mac80211 reconfig replays interface, link and
channel context setup. mt7996_vif_link_add() short-circuits when the
link_id is still marked in mvif->valid_links, a state introduced for
postponing link teardown to interface removal. The reset path frees the
link structures without clearing those bits, so the replayed setup never
re-creates dev_info/bss_info/STA records in the restarted firmware and
never re-registers the link wcid, leaving the device inoperative.
The reset path also leaks every
wifi: mt76: mt7915: fix double hif2 init on the non-WED path
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: fix double hif2 init on the non-WED path
mt7915_pci_init_hif2() was called unconditionally and again inside the
WED-inactive branch. The helper increments the global hif_idx, writes the
PCIe RECOG_ID register and takes a get_device() reference via
mt7915_pci_get_hif2(), while removal only drops one reference. On non-WED
dual-hif hardware this double-incremented hif_idx, wrote RECOG_ID twice and
leaked a device reference. Only the call inside the WED-inactive branch is
correct; drop the unconditional one. hif2 is already initialised to NULL.
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: fix ext PHY use-after-free on register error path
After mt7915_register_ext_phy() succeeded, a failure of the main PHY
mt7915_init_debugfs() or mt7915_coredump_register() unwound through
free_phy2, which called ieee80211_free_hw() on the ext PHY hw while it
was still registered with mac80211, since mt76_unregister_device() only
unregisters the main hw. Unregister the ext PHY (thermal + phy + hw)
first and skip the redundant free.
wifi: mt76: mt7915: release hif2 reference on probe IRQ failure
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: release hif2 reference on probe IRQ failure
The hif2 reference obtained by mt7915_pci_init_hif2() is only released on
error paths that key off dev->hif2, which is not assigned until after the
IRQ setup. If pci_alloc_irq_vectors() or the primary devm_request_irq()
fails, the reference leaks. Drop it explicitly on those paths via
mt7915_put_hif2().
wifi: mt76: mt7996: do not attach hif2 WED when the main WED attach failed
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: do not attach hif2 WED when the main WED attach failed
If the WED attach for the primary PCIe function fails, the probe path
still attached wed_hif2 for the secondary function, leaving the device
in an inconsistent half-WED configuration that crashes later. The hif2
call also re-enabled hwrro_mode, which the failed primary attach had
just turned off.
Skip the hif2 WED setup when the primary WED device is not active.
wifi: mt76: reject out-of-range link ids in mt76_vif_link()
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: reject out-of-range link ids in mt76_vif_link()
mt76_vif_link() indexes mvif->link[] without validating link_id, but
callers pass mvif->deflink_id / msta->deflink_id, which hold
IEEE80211_LINK_UNSPECIFIED (0xf) until the first link has been added.
Since IEEE80211_MLD_MAX_NUM_LINKS is 15, that reads one element past the
end of the array, aliasing mt76_vif_data.offchannel_link.
Reachable via mt7996_set_tsf()/mt7996_offset_tsf() and
mt7996_net_fill_forward_path(). Bounds check link_id and return NULL,
matching mt7996_sta_link() and mt7996_sta_link_protected().
wifi: mt76: mt7996: fix out-of-bounds link array access in mt7996_tx()
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: fix out-of-bounds link array access in mt7996_tx()
When mac80211 leaves the link unspecified, mt7996_tx() substitutes the
primary link id of the station or vif. That value is
IEEE80211_LINK_UNSPECIFIED (0xf) until the first link has been added,
and it is then used unchecked to index vif->link_conf[],
mvif->mt76.link[] and sta->link[], all of which hold
IEEE80211_MLD_MAX_NUM_LINKS (15) entries.
Clamp the primary link id to the default link before using it, and use
the clamped value for the link_sta fallback as well.
wifi: ath10k: snoc: use memcpy_fromio() for MSA ramdump
In the Linux kernel, the following vulnerability has been resolved:
wifi: ath10k: snoc: use memcpy_fromio() for MSA ramdump
On WCN3990/SNOC the MSA region is mapped with devm_memremap(MEMREMAP_WT).
On arm64 such a mapping is not Normal-cacheable, so unaligned accesses to
it are not permitted. ath10k_msa_dump_memory() copies the region with a
plain memcpy(), whose optimized __pi_memcpy_generic implementation issues
wide/unaligned loads. This triggers an alignment fault (FSC=0x21) Oops in
ath10k_snoc_fw_crashed_dump() while collecting the devcoredump:
Unable to handle kernel paging request ... FSC=0x21: alignment fault
pc : __pi_memcpy_g
arm64: ptrace: Keep 'orig_x0' in-sync with x0 on syscall entry
In the Linux kernel, the following vulnerability has been resolved:
arm64: ptrace: Keep 'orig_x0' in-sync with x0 on syscall entry
Commit e057b9477232 ("arm64: syscall: Ensure saved x0 is kept in-sync
with tracer updates") attempted to resolve a long-standing issue with
syscall entry tracing, where a tracer is able to manipulate the first
syscall argument without being subjected to seccomp or audit checking.
Unfortunately, that fix was incomplete [1], as it failed to update
'orig_x0' between a tracer updating x0 during a seccomp ptrace exit
(SECCOMP_RET_TRACE) and the seccomp filter being re-evaluated.
Rather than add hooks to the core se
wifi: nl80211: clean up color-change beacon data on errors
In the Linux kernel, the following vulnerability has been resolved:
wifi: nl80211: clean up color-change beacon data on errors
nl80211_color_change() calls nl80211_parse_beacon() for the beacon_next
template, which can allocate params.beacon_next.mbssid_ies and .rnr_ies.
A parsing failure returned directly instead of using the out: cleanup,
leaking any allocations completed before the error.
Allocate the nested attribute table before parsing beacon_next. Its
allocation failure can then return before beacon data exists, while a
later parsing failure uses out: to release the parsed data.
wifi: brcmfmac: fix P2P action frame handling without device vif
In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix P2P action frame handling without device vif
Some P2P action frame paths assume the P2P device vif is always
available. That is not true when userspace sends non-P2P public action
frames through the primary interface, or when action-frame abort runs
after the P2P device vif has not been created.
Fall back to the primary vif when aborting an action frame without a P2P
device vif, and guard P2P device saved IE access before using it for
peer channel search.
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: disconnect on CSA to channel 0
The refactor for the CSA parsing erroneously equates channel
zero and no information present, leading it to ignore a CSA
on an AP that advertises a switch to that (invalid) channel.
This leads to not disconnecting, which we should. For Intel
devices, this can lead to a firmware crash.
Fix this by using an int type for the channel number as well
as the opclass, and using a (negative) value that cannot be
encoded in the element to indicate it's not present.
wifi: cfg80211: stop PMSR before P2P and NAN teardown
In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: stop PMSR before P2P and NAN teardown
PMSR request teardown must abort active measurements while the
wireless_dev is still present in the driver. cfg80211_leave_locked() and
cfg80211_stop_pd() already do this before invoking the driver's stop
callback, but cfg80211_stop_p2p_device() and cfg80211_stop_nan() do not.
Those helpers are also called directly by nl80211, rfkill shutdown, and
wireless_dev unregister paths. If one of these paths stops a P2P device
or NAN interface with a pending request, it removes the mac80211
subinterface from the driver first. Su
In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix mmap_lock deadlock on arena lock failure
Reported by the Sashiko AI review.
arena_vm_fault() returns VM_FAULT_RETRY when it can't take
arena->spinlock, but it never took mmap_lock. The fault path assumes a
VM_FAULT_RETRY handler already dropped mmap_lock and re-takes it on the
retry, so mmap_lock gets taken twice and can deadlock:
do_user_addr_fault()
{
fault = handle_mm_fault(...); // calls arena_vm_fault()
if (fault & VM_FAULT_RETRY)
goto retry; // re-locks mmap_lock
mmap_read_unlock(mm);
}
Return VM_FAULT_SIGBUS instead, for two reasons:
1. W
In the Linux kernel, the following vulnerability has been resolved:
firmware: coreboot: Validate table bounds
The existing coreboot_table_populate() bounds checks limit individual
entries to the mapped length. However, coreboot_table_probe() replaces
the platform resource length with header and table sizes supplied by
firmware before mapping the full table.
A malformed table can overflow the 32-bit size addition or advertise an
extent beyond the resource, causing the driver to map and parse memory
outside the resource. A resource shorter than the fixed header is also
mapped as though it contained a complete header.
Reject resources shor
serial: amba-pl011: keep console clock enabled for atomic writes
In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: keep console clock enabled for atomic writes
pl011_console_write_atomic() runs from nbcon atomic context, where
sleeping is not allowed. It calls clk_enable(), which takes the common-clk
enable_lock. Under PREEMPT_RT that is a sleeping lock:
clk_enable_lock() first tries spin_trylock_irqsave(), but on contention
falls back to spin_lock_irqsave(). Therefore, an atomic-context printk on
an RT kernel with a clk-backed pl011 can trip:
BUG: sleeping function called from invalid context at spinlock_rt.c:48
__might_resched from rt_spin_lock
rt_spin_l
serial: core: do fallible allocations before the console can be registered
In the Linux kernel, the following vulnerability has been resolved:
serial: core: do fallible allocations before the console can be registered
serial_core_add_one_port() allocates uport->tty_groups after
uart_configure_port(), which may register the console. If the allocation
fails, the driver unwinds the port while its console remains registered.
The earlier uport->name allocation has a related failure path that leaves
state->uart_port linked to a port being freed.
Failslab reproduced a NULL dereference in PL011 console output and a KASAN
use-after-free in i.MX console output after failed binds.
Allocate the name and tty_groups before li
serial: core: clear freed pointers on uart_register_driver() failure
In the Linux kernel, the following vulnerability has been resolved:
serial: core: clear freed pointers on uart_register_driver() failure
uart_register_driver() leaves drv->state pointing to freed memory when
tty_alloc_driver() fails. If tty_register_driver() fails, drv->tty_driver
also retains a pointer after its reference is dropped.
Drivers that use drv->state as an "already registered" flag can then skip
registration on the next probe and pass the freed state to
uart_add_one_port().
This issue was found with failslab on QEMU's raspi1ap board by
failing registration and binding the PL011 port again.
Clear both pointers on their failure
In the Linux kernel, the following vulnerability has been resolved:
tty: skip cdev_del() when no cdev is registered
TTY device registration can fail before a cdev is allocated.
Serial core keeps the port so setserial can still use it, and later
removal passes the NULL cdev slot to cdev_del(), causing a NULL-pointer
dereference.
Only delete the cdev when the slot is not NULL.
In the Linux kernel, the following vulnerability has been resolved:
tty: clear cdev pointer after cdev_add() failure
tty_cdev_add() drops the cdev reference when cdev_add() fails, but
leaves driver->cdevs[index] pointing to freed memory.
tty_unregister_device() later passes that stale pointer to cdev_del(),
causing a use-after-free.
Clear the slot after dropping the reference.