Уязвимости linux-nvidia-tegra · Страница 84

power: supply: bq256xx: drain usb_work before freeing the charger

In the Linux kernel, the following vulnerability has been resolved: power: supply: bq256xx: drain usb_work before freeing the charger The USB-PHY notifier queues usb_work, whose handler calls power_supply_changed(bq->charger). The reset devm action only unregisters the notifier and was registered before the power supplies, so devm frees bq->charger on unwind before the action runs; a usb_work still queued can then dereference it. Register the reset action after the power supplies, so it unregisters the notifiers and drains usb_work before the supplies are released. Initialize usb_work and obtain the PHY references before registering the no

• Обновитесь до 5.15.0-1070.72

power: supply: charger-manager: register regulators before exposing sysfs

In the Linux kernel, the following vulnerability has been resolved: power: supply: charger-manager: register regulators before exposing sysfs charger_manager_remove() and the err_reg_extcon probe error path free each charger regulator with regulator_put() before tearing down the power_supply sysfs entries (power_supply_unregister()). charger_manager_remove() also calls try_charger_enable(cm, false) after the regulator_put() loop. A concurrent write to a charger's externally_control sysfs attribute that lands between regulator_put() and power_supply_unregister() can run charger_externally_control_store() and call try_charger_enable(), which,

power: supply: cros_usbpd-charger: bound the EC-reported port count

In the Linux kernel, the following vulnerability has been resolved: power: supply: cros_usbpd-charger: bound the EC-reported port count cros_usbpd_charger_probe() reads two port counts from the EC and uses one of them, num_charger_ports, as the loop bound when populating a fixed-size array: struct port_data *ports[EC_USB_PD_MAX_PORTS]; /* 8 entries */ ... for (i = 0; i < charger->num_charger_ports; i++) charger->ports[charger->num_registered_psy++] = port; Both num_usbpd_ports (from EC_CMD_USB_PD_PORTS) and num_charger_ports (from EC_CMD_CHARGE_PORT_COUNT) are u8 values reported by the EC. The only validation is a sanity check that c

• Обновитесь до 5.15.0-1070.72

power: supply: cros_usbpd: Limit port counts to EC_USB_PD_MAX_PORTS

In the Linux kernel, the following vulnerability has been resolved: power: supply: cros_usbpd: Limit port counts to EC_USB_PD_MAX_PORTS Currently the cros_usbpd-charger driver probe iterates based on raw charger port count returned by the embedded controller. The only check is against the number of USB PD ports which the embedded controller also defines. A malicious embedded controller could return an inaccurate port count (up to 255) resulting in an out of bounds write and subsequent memory corruption. Update helper functions in cros_usbpd-charger to limit port counts to EC_USB_PD_MAX_PORTS.

• Обновитесь до 5.15.0-1070.72

power: supply: lp8727: fix use-after-free in lp8727_release_irq()

In the Linux kernel, the following vulnerability has been resolved: power: supply: lp8727: fix use-after-free in lp8727_release_irq() lp8727_isr_func(), the threaded IRQ handler, is the only caller that arms pchg->work via schedule_delayed_work(). lp8727_release_irq() currently cancels the work before freeing the IRQ, so an IRQ delivered in between can re-arm the work through the threaded handler. After .remove returns the devm layer frees pchg while lp8727_delayed_func() may still run and dereference it. Free the IRQ first so the threaded handler is quiesced and can no longer queue work, then cancel the delayed work to drain the final g

• Обновитесь до 5.15.0-1070.72

power: supply: lp8788-charger: fix use-after-free on remove

In the Linux kernel, the following vulnerability has been resolved: power: supply: lp8788-charger: fix use-after-free on remove lp8788_charger_remove() flushes charger_work before unregistering the IRQs. An IRQ thread can queue charger_work after flush_work() has returned. The work can then run after devres frees pchg and dereference it in lp8788_charger_event(). Unregister the IRQs first. free_irq() waits for any running threaded handler, so no handler can queue more work afterwards. Then use cancel_work_sync() to cancel pending work or wait for running work to finish. This issue was found by an in-house static analysis tool.

power: supply: rt9455: quiesce delayed work before teardown

In the Linux kernel, the following vulnerability has been resolved: power: supply: rt9455: quiesce delayed work before teardown The threaded IRQ handler can queue pwr_rdy_work, max_charging_time_work and batt_presence_work. pwr_rdy_work and batt_presence_work can also queue max_charging_time_work, while batt_presence_work can requeue itself. rt9455_remove() cancels max_charging_time_work before batt_presence_work. The latter can therefore queue max_charging_time_work after it has already been cancelled: rt9455_remove() workqueue cancel pwr_rdy_work cancel max_charging_time_work

power: supply: twl4030_charger: cancel workers via devm

In the Linux kernel, the following vulnerability has been resolved: power: supply: twl4030_charger: cancel workers via devm bci is devm-allocated. Two workers (bci->work and bci->current_worker) dereference it. twl4030_bci_remove() disables charging and masks interrupts. It cancels neither worker. A worker pending at remove() can run after devm frees bci. The USB transceiver comes from devm_usb_get_phy_by_node(). devm unregisters its notifier only after remove() returns. A cancel_work_sync() in remove() can then race a notifier reschedule. devm_work_autocancel() and devm_delayed_work_autocancel() avoid that. They cancel the workers during

• Обновитесь до 5.15.0-1070.72

power: supply: ucs1002: fix use-after-free on remove

In the Linux kernel, the following vulnerability has been resolved: power: supply: ucs1002: fix use-after-free on remove ucs1002 has no remove callback, so unbind runs entirely through devm. The alert IRQ handler queues the health_poll delayed work, and the work reschedules itself while the chip reports a bad-health condition. devm frees the alert IRQ, which only synchronizes the handler; it does not cancel the delayed work, which can then run after devm frees the driver data and dereference it. Register health_poll with devm_delayed_work_autocancel() before the alert IRQ is requested. devm then frees the IRQ before cancelling the work,

• Обновитесь до 5.15.0-1070.72

power: supply: max17040: propagate register read errors

In the Linux kernel, the following vulnerability has been resolved: power: supply: max17040: propagate register read errors max17040_get_vcell() and max17040_get_soc() ignore errors returned by regmap_read(). When an I2C transfer fails, the uninitialized register value is converted and reported to userspace as a valid voltage or state of charge. The polling worker can also replace the cached state of charge with the bogus value and emit a spurious change event. Propagate read errors through the power supply get_property callback and keep the last valid cached state of charge when polling fails.

power: supply: max17040: synchronize work cancellation on suspend

In the Linux kernel, the following vulnerability has been resolved: power: supply: max17040: synchronize work cancellation on suspend max17040_work() requeues itself after every poll. cancel_delayed_work() only cancels a pending instance and does not wait for a callback that is already running. If system suspend races with the polling callback, the callback can continue accessing the fuel gauge and requeue itself after the suspend callback returns. Use cancel_delayed_work_sync() to ensure polling is quiesced before suspend completes.

• Обновитесь до 5.15.0-1070.72

s390/dasd: Do not complete a failed ESE read as successful

In the Linux kernel, the following vulnerability has been resolved: s390/dasd: Do not complete a failed ESE read as successful dasd_int_handler() completes an NRF read of an unallocated ESE track by calling ese_read() and unconditionally marking the request DASD_CQR_SUCCESS. dasd_eckd_ese_read() can return an error before it has zeroed the destination buffer: a failed sense-data parse or a current track outside the requested range both return early, leaving the destination pages untouched. The request is still completed successfully, so the block layer is handed stale / uninitialized memory instead of zeros. Check the ese_read() return val

• Обновитесь до 5.15.0-1070.72

s390/dasd: Guard sysfs discipline callbacks against unallocated private data

In the Linux kernel, the following vulnerability has been resolved: s390/dasd: Guard sysfs discipline callbacks against unallocated private data Several sysfs show/store handlers call a discipline callback that dereferences device->private, either directly or through the DASD_DEFINE_ATTR() macro. During dasd_generic_set_online() the discipline is assigned before check_device() allocates device->private, so an unprivileged read of one of these world-readable attributes in that window dereferences a NULL pointer and panics. Guard the dereference inside each callback that actually touches device->private.

• Обновитесь до 5.15.0-1070.72

s390/dasd: Propagate partial completion length across ERP recovery

In the Linux kernel, the following vulnerability has been resolved: s390/dasd: Propagate partial completion length across ERP recovery dasd_default_erp_postaction() copies the timing and device state from the finished ERP request back to the original request but drops proc_bytes. A request that was partially completed, an ESE read of a not-yet-allocated track returns fewer bytes than requested, and then recovered through the ERP chain loses its partial-completion length. __dasd_cleanup_cqr() then sees proc_bytes == 0 and completes the whole request instead of requeueing the remainder, silently returning zeroed data for the part that was nev

• Обновитесь до 5.15.0-1070.72

iommu/msm: Unwind probe state on registration failure

In the Linux kernel, the following vulnerability has been resolved: iommu/msm: Unwind probe state on registration failure msm_iommu_probe() adds its devm-managed IOMMU object to qcom_iommu_devices before adding the IOMMU sysfs device and registering it with the IOMMU core. If iommu_device_sysfs_add() fails, probe returns with the object still on qcom_iommu_devices. The driver core then releases the devm allocation, leaving a dangling list entry that later list walks may dereference. If iommu_device_register() fails, the same dangling list entry remains and the sysfs device is left registered as well. Unwind the sysfs device and global li

iommu/vt-d: Force requesting ACS when tboot is enabled

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Force requesting ACS when tboot is enabled Currently the conditions of requesting ACS in detect_intel_iommu() don't include tboot, leading to a possible misconfiguration with ACS disabled (e.g. due to user opts) while iommu is later forced on by tboot_force_iommu(). Fix it by checking tboot in detect_intel_iommu().

platform/x86: dell-wmi-sysman: Don't hex dump attribute security buffer

In the Linux kernel, the following vulnerability has been resolved: platform/x86: dell-wmi-sysman: Don't hex dump attribute security buffer set_attribute() populates the security area of the BIOS attribute request buffer with the current admin password via populate_security_buffer(), then dumps the whole request buffer with print_hex_dump_bytes(). This can expose the plaintext admin password in the kernel log. The same issue was fixed for the password attribute path by commit d1a196e0a6dc ("platform/x86: dell-wmi-sysman: Don't hex dump plaintext password data"). Remove the remaining dump from the BIOS attribute path.

• Обновитесь до 5.15.0-1070.72

mmc: via-sdmmc: cancel card-detect work on remove

In the Linux kernel, the following vulnerability has been resolved: mmc: via-sdmmc: cancel card-detect work on remove Disabling the device interrupt and freeing the IRQ prevents new card-detect work from being queued, but carddet_work already queued by the handler can still run after via_sd_remove() returns. via_sdc_card_detect() recovers the host through container_of() and dereferences its MMIO base; once remove() returns the host can be freed, so that work would touch freed memory. Cancel carddet_work after freeing the IRQ and before cancelling finish_bh_work, which the card-detect handler can also queue. carddet_work can re-enable the i

mmc: via-sdmmc: stop card-detect handling on probe failure

In the Linux kernel, the following vulnerability has been resolved: mmc: via-sdmmc: stop card-detect handling on probe failure request_irq() registers the SD card-detect interrupt and the probe enables it before mmc_add_host() runs. If mmc_add_host() fails, the error path only unmaps the registers and returns: the interrupt stays registered, so the handler keeps running against the host once it is freed. via_sdc_isr() dereferences sdhost and its MMIO base and schedules carddet_work, which via_sdc_card_detect() also runs against freed memory through its container_of() dereference. Add a probe-error path that disables and frees the interrupt

• Обновитесь до 5.15.0-1070.72

platform/x86: int1092: Fix potential memory leak in sar_probe()

In the Linux kernel, the following vulnerability has been resolved: platform/x86: int1092: Fix potential memory leak in sar_probe() The memory allocated for device_mode_info in parse_package() called by sar_get_data() is not freed in some of the error paths in sar_probe(). Fix that by converting to use device managed allocations.