Уязвимости linux-ibm-5.15 · Страница 95

s390/qeth: validate user buffer length in SNMP and ARP query ioctls

In the Linux kernel, the following vulnerability has been resolved: s390/qeth: validate user buffer length in SNMP and ARP query ioctls qeth_snmp_command() and qeth_l3_arp_query() allocate a buffer sized by a user-supplied length (udata_len) without checking a lower bound, then set udata_offset to a fixed non-zero value and pass both to a reply callback. The callback bounds-checks the copy with if ((udata_len - udata_offset) < len) Both fields are u32, so a udata_len smaller than udata_offset makes the subtraction wrap and the check pass, and the following memcpy() writes past the allocation. A udata_len of 0 also yields ZERO_SIZE

• Обновитесь до 5.15.0-1113.117~20.04.1

ASoC: codecs: lpass-tx-macro: Fix enum kcontrol accesses

In the Linux kernel, the following vulnerability has been resolved: ASoC: codecs: lpass-tx-macro: Fix enum kcontrol accesses The "DEC0 MODE" to "DEC7 MODE" controls are enumerated, but tx_macro_dec_mode_get() and tx_macro_dec_mode_put() access their value through ucontrol->value.integer.value[0] (a long) instead of ucontrol->value.enumerated.item[0] (an unsigned int). This same pattern was fixed in the sibling drivers by commit bcfe5f76cc40 ("ASoC: codecs: rx-macro: fix accessing array out of bounds for enum type") and commit 0ea5eff7c606 ("ASoC: codecs: va-macro: fix accessing array out of bounds for enum type"), but tx-macro was missed.

• Обновитесь до 5.15.0-1113.117~20.04.1

fbdev: bound mode sysfs output to the sysfs buffer

In the Linux kernel, the following vulnerability has been resolved: fbdev: bound mode sysfs output to the sysfs buffer mode_string() uses snprintf() which can return a value larger than the remaining buffer space. show_modes() accumulates the return value into i without checking whether i has reached PAGE_SIZE, causing the offset to advance past the sysfs buffer if the modelist is long enough. Add a size parameter to mode_string() and use scnprintf() to return only the bytes actually written. Add an early return when offset already exceeds the buffer. In show_modes(), stop accumulating once the buffer is full.

fbdev: clear fb_info->mode before deleting a videomode

In the Linux kernel, the following vulnerability has been resolved: fbdev: clear fb_info->mode before deleting a videomode fb_set_var() can delete a mode from info->modelist when userspace passes FB_ACTIVATE_INV_MODE through FBIOPUT_VSCREENINFO. The code checks that the mode being deleted is not the current info->var and that fbcon is not using it, but it does not check fb_info->mode. fb_info->mode may still point into the modelist entry being deleted. If the entry is freed, later mode sysfs reads through show_mode() can dereference a stale pointer. Clear fb_info->mode before calling fb_delete_videomode() when it matches the mode being re

drm/amdgpu: reject oversized IBs with per-ring packet limits

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: reject oversized IBs with per-ring packet limits On GFX rings, amdgpu_cs_p2_ib() passed user-supplied ib_bytes through to ib->length_dw without a limit, while ring_emit_ib() encodes length into packet fields. Oversized values can corrupt adjacent control bits and destabilize command submission. Add a per-ring IB packet size limit helper and reject command submissions exceeding the corresponding dword limit before IB allocation. Use the documented 20-bit limit for GFX/compute/SDMA/VPE, and apply the MM fallback limit for other ring types. (cherry picked from co

Input: focaltech - fix array out-of-bounds in focaltech_process_rel_packet

In the Linux kernel, the following vulnerability has been resolved: Input: focaltech - fix array out-of-bounds in focaltech_process_rel_packet Make finger2 (and also finger1) unsigned, so that if the finger index in the packet is 0 then subtracting 1 creates an array index which overflows above the existing check for FOC_MAX_FINGERS, as the existing comment says it should, instead of writing to state->fingers[-1].

• Обновитесь до 5.15.0-1113.117~20.04.1

Input: iforce - validate input packet lengths

In the Linux kernel, the following vulnerability has been resolved: Input: iforce - validate input packet lengths iforce_process_packet() reads fixed fields from joystick, wheel and status packets without first checking their lengths. In particular, the shared hats-and-buttons helper unconditionally reads data[6]. The status tail is a sequence of 16-bit effect addresses, but an incomplete final address is also consumed. A successful zero-length USB URB additionally reads the packet ID before the common parser is called. Reject the zero-length USB transfer, require the seven-byte joystick and wheel prefixes and the two-byte status prefix, a

• Обновитесь до 5.15.0-1113.117~20.04.1

Input: byd - synchronize timer deletion before freeing private data

In the Linux kernel, the following vulnerability has been resolved: Input: byd - synchronize timer deletion before freeing private data byd_disconnect() uses timer_delete() before freeing the driver's private data. This does not wait for a running byd_clear_touch() callback, which dereferences the private data and its psmouse pointer. A callback racing with disconnect can therefore access the private data after it has been freed. The timer can also still be re-armed by byd_process_byte() while the disconnect is in progress. Use timer_shutdown_sync() before freeing the private data: it waits for a running callback and turns any later re-

Input: synaptics-rmi4 - zero report size on F54 work error

In the Linux kernel, the following vulnerability has been resolved: Input: synaptics-rmi4 - zero report size on F54 work error In rmi_f54_work(), if an error occurs during report request or command verification, the code jumped directly to the 'error' label, bypassing the 'abort' label where f54->report_size was normally zeroed out. This left f54->report_size containing its previous successful payload size. If a user then altered the V4L2 format to a smaller size, and a subsequent run failed, rmi_f54_buffer_queue() would copy the stale, larger payload size into the shrunken V4L2 buffer, causing a heap buffer overflow. Fix this by merging

• Обновитесь до 5.15.0-1113.117~20.04.1

Input: synaptics-rmi4 - bound the F54 report size to the allocated buffer

In the Linux kernel, the following vulnerability has been resolved: Input: synaptics-rmi4 - bound the F54 report size to the allocated buffer rmi_f54_work() reads a diagnostics report from the device into f54->report_data, sizing the transfer with rmi_f54_get_report_size(): report_size = rmi_f54_get_report_size(f54); ... for (i = 0; i < report_size; i += F54_REPORT_DATA_SIZE) { int size = min(F54_REPORT_DATA_SIZE, report_size - i); ... rmi_read_block(.., f54->report_data + i, size); } report_data is allocated once at probe from F54's own electrode counts (array3_size(f54->num_tx_electrodes, f54->num_rx_electrodes, sizeof(u16))),

• Обновитесь до 5.15.0-1113.117~20.04.1

Input: synaptics-rmi4 - block s_input when F54 queue is busy

In the Linux kernel, the following vulnerability has been resolved: Input: synaptics-rmi4 - block s_input when F54 queue is busy Changing the input (diagnostic report type) mid-stream changes the report size. Since V4L2 buffers are allocated based on the size at stream start, changing the input while streaming could lead to a heap buffer overflow if the new size is larger than the allocated buffers. Prevent this by blocking VIDIOC_S_INPUT with -EBUSY if the V4L2 queue is busy (streaming).

• Обновитесь до 5.15.0-1113.117~20.04.1

Input: synaptics-rmi4 - propagate F54 worker errors to V4L2 queue

In the Linux kernel, the following vulnerability has been resolved: Input: synaptics-rmi4 - propagate F54 worker errors to V4L2 queue Previously, rmi_f54_buffer_queue() waited for the worker thread to finish but ignored whether it succeeded. If the worker failed (e.g., due to a timeout or register read failure), the queue thread would silently return success, delivering stale or uninitialized memory to userspace. Add a 'report_error' field to struct f54_data to store the worker's exit status. Check this field in rmi_f54_buffer_queue() after the worker finishes, and mark the buffer as VB2_BUF_STATE_ERROR if an error occurred.

• Обновитесь до 5.15.0-1113.117~20.04.1

crypto: qce - fix error path in devm_qce_register_algs

In the Linux kernel, the following vulnerability has been resolved: crypto: qce - fix error path in devm_qce_register_algs If ops->register_algs() fails, the error path repeatedly calls the same ops->unregister_algs() from the failed registration. Use the loop index to unregister the previously registered algorithms instead.

• Обновитесь до 5.15.0-1113.117~20.04.1

gpio: ml-ioh: use raw_spinlock_t for the register lock

In the Linux kernel, the following vulnerability has been resolved: gpio: ml-ioh: use raw_spinlock_t for the register lock ioh_irq_type() is registered as the irq_chip .irq_set_type callback and takes chip->spinlock with spin_lock_irqsave(). This callback is reached from __setup_irq() -> __irq_set_trigger() -> chip->irq_set_type() while the caller holds desc->lock, a raw_spinlock_t, with hardirqs disabled. That context is not sleepable, but on PREEMPT_RT a regular spinlock_t is an rtmutex-backed sleeping lock, so acquiring it there is invalid. ioh_irq_enable() and ioh_irq_disable() take the same lock from the .irq_enable/.irq_disable callb

• Обновитесь до 5.15.0-1113.117~20.04.1

libceph: fix multiple unsafe decodes in decode_locker()

In the Linux kernel, the following vulnerability has been resolved: libceph: fix multiple unsafe decodes in decode_locker() decode_locker() in cls_lock_client.c contains three unsafe decode operations that allow a malicious or compromised OSD to trigger slab-out-of-bounds reads: 1. ceph_decode_copy() at the locker_id_t name field has no preceding bounds check. With p == end after ceph_start_decoding() accepts struct_len=0, this reads sizeof(ceph_entity_name) = 9 bytes past the validated buffer boundary. 2. *p += sizeof(struct ceph_timespec) after the locker_info_t header is an unchecked pointer advance. A malicious OSD can pos

• Обновитесь до 5.15.0-1113.117~20.04.1

openrisc: signal: do not restore privileged SR bits on sigreturn

In the Linux kernel, the following vulnerability has been resolved: openrisc: signal: do not restore privileged SR bits on sigreturn restore_sigcontext() copies the whole supervision register (SR) from the signal frame and only clears SPR_SR_SM before the value is reloaded into the hardware SR (through ESR and l.rfe) on the return to user space. All other SR bits are left under user control. An unprivileged task can thus return from a signal handler through a crafted sigframe that clears SPR_SR_DME. With the data MMU disabled the CPU performs no translation or protection on data accesses, so the task gains read and write access to arbitr

• Обновитесь до 5.15.0-1113.117~20.04.1

Input: sur40 - fix input device registration ordering

In the Linux kernel, the following vulnerability has been resolved: Input: sur40 - fix input device registration ordering In sur40_probe(), input_register_device() was previously called early before the V4L2 video device and vb2_queue components were fully initialized. If userspace opened the input device immediately upon registration, sur40_open() would trigger and start the sur40_poll() worker thread. This worker thread invokes sur40_process_video() and accesses the uninitialized vb2_queue structure, leading to a data race and potential system crash. Furthermore, if V4L2 or video registration failed after input_register_device() succeede

• Обновитесь до 5.15.0-1113.117~20.04.1

libceph: Avoid using invalid osd indices from primary_temp

In the Linux kernel, the following vulnerability has been resolved: libceph: Avoid using invalid osd indices from primary_temp A corrupted osdmap received from a Ceph monitor or OSD may contain osd indices in its pg_temp, primary_temp, pg_upmap, and pg_upmap_items parts that don't exist, i.e., that are greater than max_osd or smaller than CEPH_HOMELESS_OSD (-1). These indices are used to create the up and acting set in ceph_pg_to_up_acting_osds(), called from calc_target(). While most of these osd indices are checked, the one from primary_temp is not. Subsequently, this may lead to calc_target() returning this (potentially invalid) index as

• Обновитесь до 5.15.0-1113.117~20.04.1

libceph: fix OOB read in decode_watchers() via missing bounds check

In the Linux kernel, the following vulnerability has been resolved: libceph: fix OOB read in decode_watchers() via missing bounds check ceph_start_decoding() validates that struct_len bytes remain in the buffer after the encoding header, but accepts struct_len=0 as valid: ceph_decode_need(p, end, 0, bad) always passes. When a malicious or compromised OSD sends an obj_list_watch_response_t reply with struct_len=0, ceph_start_decoding() returns success with p == end, leaving zero bytes guaranteed for subsequent reads. The immediately following ceph_decode_32(p) in decode_watchers() has no preceding bounds check. With p == end this is a 4-byt

• Обновитесь до 5.15.0-1113.117~20.04.1

mmc: atmel-mci: Fix use-after-free in atmci_remove due to race condition

In the Linux kernel, the following vulnerability has been resolved: mmc: atmel-mci: Fix use-after-free in atmci_remove due to race condition In atmci_probe, &host->bh_work is bound with atmci_work_func, and atmci_interrupt, atmci_timeout_timer and atmci_dma_complete can all queue this work on system_bh_wq. If we remove the module, atmci_remove makes cleanup and the memory allocated for host with devm_kzalloc() is released after the remove callback returns, while the work mentioned above may still be pending or running. The sequence of operations that may lead to a UAF bug is as follows: CPU0 CPU1