block: stop the timeout timer when releasing a never added disk
In the Linux kernel, the following vulnerability has been resolved:
block: stop the timeout timer when releasing a never added disk
disk_release() undoes blk_mq_init_allocated_queue() for a disk whose
probe failed before add_disk(), but it only calls blk_mq_exit_queue().
Nothing there stops q->timeout, and that timer rolls forward: it stays
pending until it next expires, not until the last request completes.
So if the driver issued any I/O before adding the disk, the
request_queue is freed while still linked into a timer wheel bucket.
Commit 6f8191fdf41d ("block: simplify disk shutdown") dropped the
blk_cleanup_queue() call that used to st
In the Linux kernel, the following vulnerability has been resolved:
mptcp: avoid combining some incoming suboptions
Some MPTCP suboptions are mutually exclusive according to the RFC8684,
but also because in different places, the code doesn't expect some
combinations to be present. That's specially true for suboptions that
would be present twice, but with different attributes.
The new restrictions are the same as the ones applied on the output
side, with mptcp_write_options. The same rules can be reused with a
small fix: an MP_FASTCLOSE can be used with a DSS when the sender picks
this option [1], which is not the case on Linux. Here are th
mptcp: options: reset DSS fields in case of unexpected size
In the Linux kernel, the following vulnerability has been resolved:
mptcp: options: reset DSS fields in case of unexpected size
A remote peer could send a malformed DSS with a wrong size, followed by
another DSS or MPC + Data. In this case, the first suboption will be
ignored, but leaving some fields written, which could lead to
inconsistency or access uninitialized data.
Explicitly reset the fields that could have been modified in case of
unexpected size.
mptcp: fastopen: only mark MPTFO subflows with SYN data
In the Linux kernel, the following vulnerability has been resolved:
mptcp: fastopen: only mark MPTFO subflows with SYN data
Passive TCP Fast Open accepts a valid-cookie SYN even when it carries
no data. In that case the child socket's receive queue is intentionally
left empty.
mptcp_fastopen_subflow_synack_set_params() set is_mptfo before checking
for queued SYN data. That made data-less TFO SYNs hit a WARN and, if
the warning was non-fatal, left stale MPTFO state behind. The stale
flag could later trigger a state-confusion bug in
check_fully_established().
Only mark the subflow as MPTFO after confirming that an SKB was queued.
Return qui
Высокий · CVSS 8.4EPSS 0,2%Нет опубликованного исправления
s390/qeth: validate user buffer length in SNMP and ARP query ioctls
In the Linux kernel, the following vulnerability has been resolved:
s390/qeth: validate user buffer length in SNMP and ARP query ioctls
qeth_snmp_command() and qeth_l3_arp_query() allocate a buffer sized by
a user-supplied length (udata_len) without checking a lower bound, then
set udata_offset to a fixed non-zero value and pass both to a reply
callback. The callback bounds-checks the copy with
if ((udata_len - udata_offset) < len)
Both fields are u32, so a udata_len smaller than udata_offset makes the
subtraction wrap and the check pass, and the following memcpy() writes
past the allocation. A udata_len of 0 also yields ZERO_SIZE
In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: lpass-tx-macro: Fix enum kcontrol accesses
The "DEC0 MODE" to "DEC7 MODE" controls are enumerated, but
tx_macro_dec_mode_get() and tx_macro_dec_mode_put() access their
value through ucontrol->value.integer.value[0] (a long) instead of
ucontrol->value.enumerated.item[0] (an unsigned int).
This same pattern was fixed in the sibling drivers by
commit bcfe5f76cc40 ("ASoC: codecs: rx-macro: fix accessing array
out of bounds for enum type") and
commit 0ea5eff7c606 ("ASoC: codecs: va-macro: fix accessing array
out of bounds for enum type"), but tx-macro was missed.
Без оценкиEPSS 0,21%Нет опубликованного исправления
ASoC: SOF: ipc4-pcm: Continue the pipeline trigger in case of IPC timeout
In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: ipc4-pcm: Continue the pipeline trigger in case of IPC timeout
Ignore IPC errors for pipeline state change if the firmware state is
crashed or the IPC has timed out.
If the firmware has crashed the kernel still needs to go through the state
changes to reset its internal to be able to correctly work the next time
the DSP is booted up.
The case with IPC timeout is a bit more problematic, but it has been
rootcaused to be the result of system scheduling blockage and the firmware
did actually received and handled the message, but the reply handling got
blocked by is
Высокий · CVSS 7.8EPSS 0,11%Нет опубликованного исправления
fbdev: bound mode sysfs output to the sysfs buffer
In the Linux kernel, the following vulnerability has been resolved:
fbdev: bound mode sysfs output to the sysfs buffer
mode_string() uses snprintf() which can return a value larger than the
remaining buffer space. show_modes() accumulates the return value into i
without checking whether i has reached PAGE_SIZE, causing the offset to
advance past the sysfs buffer if the modelist is long enough.
Add a size parameter to mode_string() and use scnprintf() to return
only the bytes actually written. Add an early return when offset
already exceeds the buffer. In show_modes(), stop accumulating once
the buffer is full.
Высокий · CVSS 7.8EPSS 0,11%Нет опубликованного исправления
fbdev: clear fb_info->mode before deleting a videomode
In the Linux kernel, the following vulnerability has been resolved:
fbdev: clear fb_info->mode before deleting a videomode
fb_set_var() can delete a mode from info->modelist when userspace
passes FB_ACTIVATE_INV_MODE through FBIOPUT_VSCREENINFO. The code
checks that the mode being deleted is not the current info->var and
that fbcon is not using it, but it does not check fb_info->mode.
fb_info->mode may still point into the modelist entry being deleted.
If the entry is freed, later mode sysfs reads through show_mode() can
dereference a stale pointer.
Clear fb_info->mode before calling fb_delete_videomode() when it
matches the mode being re
Высокий · CVSS 7.3EPSS 0,12%Нет опубликованного исправления
fbdev: core: Fix pointer desynchronization in fb_io_read()
In the Linux kernel, the following vulnerability has been resolved:
fbdev: core: Fix pointer desynchronization in fb_io_read()
In fb_io_read(), if copy_to_user() performs a partial copy (e.g., due to
a faulty user buffer), the loop adjusts the chunk size 'c' and updates
the remaining 'count'. However, the hardware 'src' pointer has already
been eagerly advanced by the original chunk size.
If the loop is allowed to continue, the read will resume from an
incorrect, over-advanced offset. Since the remaining 'count' was only
decremented by the successful bytes, this desynchronization causes the
next iterations to execute more hardware reads th
Высокий · CVSS 8.8EPSS 0,12%Нет опубликованного исправления
drm/amdgpu: reject oversized IBs with per-ring packet limits
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: reject oversized IBs with per-ring packet limits
On GFX rings, amdgpu_cs_p2_ib() passed user-supplied ib_bytes through
to ib->length_dw without a limit, while ring_emit_ib() encodes length
into packet fields. Oversized values can corrupt adjacent control bits
and destabilize command submission.
Add a per-ring IB packet size limit helper and reject command
submissions exceeding the corresponding dword limit before IB
allocation. Use the documented 20-bit limit for GFX/compute/SDMA/VPE,
and apply the MM fallback limit for other ring types.
(cherry picked from co
Высокий · CVSS 8.4EPSS 0,13%Нет опубликованного исправления
Input: focaltech - fix array out-of-bounds in focaltech_process_rel_packet
In the Linux kernel, the following vulnerability has been resolved:
Input: focaltech - fix array out-of-bounds in focaltech_process_rel_packet
Make finger2 (and also finger1) unsigned, so that if the finger index in
the packet is 0 then subtracting 1 creates an array index which overflows
above the existing check for FOC_MAX_FINGERS, as the existing comment says
it should, instead of writing to state->fingers[-1].
Без оценкиEPSS 0,22%Нет опубликованного исправления
Input: iforce - validate input packet lengths
In the Linux kernel, the following vulnerability has been resolved:
Input: iforce - validate input packet lengths
iforce_process_packet() reads fixed fields from joystick, wheel and
status packets without first checking their lengths. In particular, the
shared hats-and-buttons helper unconditionally reads data[6]. The status
tail is a sequence of 16-bit effect addresses, but an incomplete final
address is also consumed. A successful zero-length USB URB additionally
reads the packet ID before the common parser is called.
Reject the zero-length USB transfer, require the seven-byte joystick and
wheel prefixes and the two-byte status prefix, a
Высокий · CVSS 7.8EPSS 0,12%Нет опубликованного исправления
Input: byd - synchronize timer deletion before freeing private data
In the Linux kernel, the following vulnerability has been resolved:
Input: byd - synchronize timer deletion before freeing private data
byd_disconnect() uses timer_delete() before freeing the driver's private
data. This does not wait for a running byd_clear_touch() callback, which
dereferences the private data and its psmouse pointer. A callback racing
with disconnect can therefore access the private data after it has been
freed. The timer can also still be re-armed by byd_process_byte() while
the disconnect is in progress.
Use timer_shutdown_sync() before freeing the private data: it waits for
a running callback and turns any later re-
Высокий · CVSS 7.8EPSS 0,14%Нет опубликованного исправления
Input: synaptics-rmi4 - zero report size on F54 work error
In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - zero report size on F54 work error
In rmi_f54_work(), if an error occurs during report request or command
verification, the code jumped directly to the 'error' label, bypassing
the 'abort' label where f54->report_size was normally zeroed out.
This left f54->report_size containing its previous successful payload
size. If a user then altered the V4L2 format to a smaller size, and a
subsequent run failed, rmi_f54_buffer_queue() would copy the stale,
larger payload size into the shrunken V4L2 buffer, causing a heap
buffer overflow.
Fix this by merging
Высокий · CVSS 7.8EPSS 0,12%Нет опубликованного исправления
Input: synaptics-rmi4 - bound the F54 report size to the allocated buffer
In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - bound the F54 report size to the allocated buffer
rmi_f54_work() reads a diagnostics report from the device into
f54->report_data, sizing the transfer with rmi_f54_get_report_size():
report_size = rmi_f54_get_report_size(f54);
...
for (i = 0; i < report_size; i += F54_REPORT_DATA_SIZE) {
int size = min(F54_REPORT_DATA_SIZE, report_size - i);
...
rmi_read_block(.., f54->report_data + i, size);
}
report_data is allocated once at probe from F54's own electrode counts
(array3_size(f54->num_tx_electrodes, f54->num_rx_electrodes, sizeof(u16))),
Высокий · CVSS 7.8EPSS 0,19%Нет опубликованного исправления
Input: synaptics-rmi4 - block s_input when F54 queue is busy
In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - block s_input when F54 queue is busy
Changing the input (diagnostic report type) mid-stream changes the
report size. Since V4L2 buffers are allocated based on the size at
stream start, changing the input while streaming could lead to a
heap buffer overflow if the new size is larger than the allocated
buffers.
Prevent this by blocking VIDIOC_S_INPUT with -EBUSY if the V4L2 queue
is busy (streaming).
Без оценкиEPSS 0,17%Нет опубликованного исправления
Input: synaptics-rmi4 - propagate F54 worker errors to V4L2 queue
In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - propagate F54 worker errors to V4L2 queue
Previously, rmi_f54_buffer_queue() waited for the worker thread to
finish but ignored whether it succeeded. If the worker failed (e.g.,
due to a timeout or register read failure), the queue thread would
silently return success, delivering stale or uninitialized memory to
userspace.
Add a 'report_error' field to struct f54_data to store the worker's exit
status. Check this field in rmi_f54_buffer_queue() after the worker
finishes, and mark the buffer as VB2_BUF_STATE_ERROR if an error
occurred.
Без оценкиEPSS 0,16%Нет опубликованного исправления
Input: hynitron_cstxxx - validate touch count and finger IDs
In the Linux kernel, the following vulnerability has been resolved:
Input: hynitron_cstxxx - validate touch count and finger IDs
The driver allocates max_touch_num input slots, which are indexed from
zero through max_touch_num - 1. The current check allows a finger ID
equal to max_touch_num to reach cst3xx_report_contact(). While the input
core ignores out-of-range slot indices, reporting touch data without a
valid slot change corrupts the touch state of the previously active slot.
The touch count is read from the controller's report and is used to
index the fixed-size report buffer without first checking its range.
Reject counts larger th
Высокий · CVSS 7.8EPSS 0,18%Нет опубликованного исправления
crypto: qce - fix error path in devm_qce_register_algs
In the Linux kernel, the following vulnerability has been resolved:
crypto: qce - fix error path in devm_qce_register_algs
If ops->register_algs() fails, the error path repeatedly calls the same
ops->unregister_algs() from the failed registration. Use the loop index
to unregister the previously registered algorithms instead.